NET Framework Installation Error Code 0x80071a90

Код ошибки код 80071a90

Error code 0x80071a90 could emerge as a result of a myriad of factors. For lots of users, the error code shows up when attempting to install the. net framework in Windows 10. Many Windows users have actually reported being met with error code 0X80071A90 when aiming to install the. NET Framework on their computers or when trying to enable Hyper-V on Windows 8 or Windows 10.

The error code is often followed by a message that, “The function attempted to use a name that is reserved for use by another Transaction”.

Fixing Error Code 0x80071a90

Method 1: Disable Antivirus

If the error occurs when you are trying to install the Hyper-V feature and you are making use of the Avast anti-virus program, then you could quickly solve it by shutting down your antivirus and turning off any type of software application that may be making use of the virtual machine.

You can disable your antivirus by running it and choosing the Disable option. Please refer to the manufacturer website on specific ways of disabling it.

Method 2: Run an SFC scan

One of the very first things you should try when faced with error code 0X80071A90 is running an SFC scan. The method entails finding and fixing any errors using the System File Checker tool.

The process should proceed until it is 100% complete. It should show a message that it has successfully fixed the corrupt files. It indicates that the process has actually been completed successfully, and the error code 0x80071a90 will be fixed.

Method 3: Perform a Clean Boot

You can also resolve the error code through a clean boot. To do a Clean boot, you must follow below mentioned steps.

Method 4: See if the problem persists in Safe Mode

This issue generally arises due to another process or program interfering with what you are attempting to get Windows to perform for you. Well, no third-party program or application can interfere with what you are doing if all them are disabled– which is exactly just what Safe Mode is for. To get to the safe mode:

When trying to restore the system using System Restore, the program may fail to work and throw up the following error message – System Restore did not complete successfully. An unspecified error occurred 0x80071a90. If you face this issue, then this post may help you fix the issue.

System Restore did not complete successfully, Error Code 0x80071a90

System Restore did not complete successfully

System Restore failed to replace the file with its original copy from the restore point.

An unspecified error occurred during System Restore (0x80071a90)

See the detailed description below!

1] Check available Disk Space

Disk Space not avaialble

You can’t just keep adding stuff to a drive and leave it that way. It should be checked for the free space available from time to time. The same principle applies when you have System Restore enabled. Check if you have sufficient Disk space available when you get the ‘System Restore did not complete successfully’ error message. If not, use Disk Cleanup Tool to clear out junk files. hen, proceed with the process.

2] Ensure that System Restore is enabled

system restore disabled

It is particularly important to verify that System Restore is enabled on the desired drive. Sometimes, you try the operation on a different drive, and therefore it fails to complete.

3] Check the status of Services

It’s fairly easy to check the status of services in Windows. Simply type Services. msc in Start Menu Search Box and hit Enter.

Now, make sure that the Volume Shadow Copy & Task Scheduler & Microsoft Software Shadow Copy Provider Service is Running and set on Automatic.

Also, if the Status of System Restore Service is Not Started, Start it and set the same to Automatic.

4] Repair system image

A system image represents an exact copy of a drive. It allows you to return your computer to the state that existed at the time when the backup was created. If it gets damaged due to corruption or some unknown reason, you can run the DISM tool to repair a corrupted Windows System Image and remove the error message.

5] Reset the repository

If your Windows device is experiencing trouble reading from the Windows Management Interface (WMI) repository, you may need to reset the repository as a troubleshooting step. For this,

Boot into Safe Mode without networking and open a command prompt as administrator.

In the Command Prompt window, type the following and hit Enter:

The action when confirmed will stop the Windows Management Instrumentation Service

Next, go to C:\Windows\System32\wbem and rename the repository folder to repositoryold.

Again open a command prompt as administrator, type the following, and hit Enter:

thereafter, type the following and press Enter key.

Now, simply restart your PC and check if you can create a System Restore Point manually.

6] Create System Restore Point in Clean Boot State

7] Disable security software temporarily

Sometimes, the security software you run to protect your system and its files interferes with the System Restore process. As such, disable the anti-virus or anti-malware program you have enabled and try the System Restore again.

8] Check Event Logs

Windows logs events, especially ones pertaining to backups on a regular basis. You can use this information to pinpoint the cause and fix it quickly.

Type eventvwr. msc /s in Search Box & hit Enter to open the Event Viewer.

Here, double-click on Applications & Services Logs to see if you are able to evaluate the event description or the cause of the problem.

Источники:

https://droidov. com/oshibka-80070103-pri-obnovlenii-windows-7-kak-ispravit

https://ru. deniskomlev. com/code-80070103-windows-update-error

https://www. earthslab. com/computer-science/error-code-0x80071a90/

https://www. thewindowsclub. com/system-restore-did-not-complete-successfully-0x80071a90

Понравилась статья? Поделиться с друзьями:
Добавить комментарий

;-) :| :x :twisted: :smile: :shock: :sad: :roll: :razz: :oops: :o :mrgreen: :lol: :idea: :grin: :evil: :cry: :cool: :arrow: :???: :?: :!: